№ 795 (2014)

УДК 666.940.41

П. Ванкевич1, Є. Пістун2, В. Фединець2
1Академія Сухопутних військ імені Петра Сагайдачного,
2Національний університет “Львівська політехніка”

ВПЛИВ РОБОЧОГО ТЕПЛОВОГО НАВАНТАЖЕННЯ НА РОЗРАХУНОК КОНСТРУКТИВНИХ ПАРАМЕТРІВ ОПОРНОГО ВУЗЛА ОБЕРТОВОГО ТЕПЛОТЕХНІЧНОГО АГРЕГАТА

© Ванкевич П., Пістун Є, Фединець В., 2014

Проведено дослідження впливу теплового навантаження на перерозподіл напружено-деформівного стану структурних елементів обертових теплотехнічних агрегатів.
Ключові слова: теплове навантаження, параметричний аналіз, обертовий теплотехнічний агрегат (ОТА), конструктивні параметри ОТА.

The improved construction of main unit of rotational thermal plant (RTP) is presented in the paper. The main unit is made of a system of contact rollers and a belt. The influence of thermal load on distribution of strain and stress state of the main unit and of other parts of RTP is studied. The most probable points with possible defects are defined on the basis of the study. Optimization of parameters of the main unit is made, i.e. the belt is mounted on the body of the main unit with a fixed thermal clearance by means of spring elements.
Key words: thermal load, parametric analysis, rotational thermal plant (RTP), design parameters of RTP.

Кількість посилань 12

УДК 536.2.083.

І. С. Васильківський, Я. П. Юсик
Національний університет “Львівська політехніка”

ВИСОКОТОЧНИЙ КОМПАРАТОР ТЕПЛОПРОВІДНОСТІ ДЛЯ ВИЗНАЧЕННЯ МАЛИХ ВІДХИЛЕНЬ ТЕПЛОПРОВІДНОСТІ ВЗІРЦІВ ТВЕРДИХ МАТЕРІАЛІВ

© Васильківський І.С., Юсик Я.П., 2014

Наведено теоретичні основи побудови компаратора для визначення відхилень теплопровідності взірців твердих матеріалів на основі зрівноваженої мостової теплової вимірювальної схеми, наводиться опис принципової схеми розробленого компаратора та результати експериментальних досліджень.
Ключові слова: теплопровідність, тепловий опір, теплова вимірювальна схема.

The development of modern science and industry is largely associated with the emergence of new, artificially created materials for which thermal conductivity is a certified option. Devices for testing the materials in Ukraine were established. In addition, the actual problem is the transmission unit size of the thermal conductivity of national primary standards for working standards. This creates great difficulties both in terms of implementation materials testing and metrological support in these measurements. In the article the theoretical bases of the comparator to determine the thermal conductivity of small deviations of the thermal conductivity of solid material models based on balanced bridge circuit heat are described. The structural scheme of the developed comparator shows the method of choosing optimal parameters for comparator elements by the criterion of maximum sensitivity of the circuit. Building a comparator to determine the thermal conductivity of small deviations of the thermal conductivity of solid material models based on balanced bridge thermal measuring system allows to improve significantly the accuracy of small deviations of the thermal conductivity of different models, in particular - the same size and made of the same material as compared to other known schemes for reducing the impact of different uninformative parameters.
Key words: thermal conductivity, thermal resistance, thermal measuring system.

Кількість посилань 6

УДК 621.184.4/.5

І.Р. Галянчук, М.Я. Кузнецова
Національний університет “Львівська політехніка”

МАТЕМАТИЧНЕ МОДЕЛЮВАННЯ ТА ДОСЛІДЖЕННЯ ВЛАСТИВОСТЕЙ ПОВІТРОПІДІГРІВНИКА КОТЛА

© Галянчук І.Р., Кузнецова М.Я., 2014

Запропоновано спеціальну структурну схему та відповідну математичну модель повітропідігрівника як системи взаємопов’язаних теплообмінників. Отримані результати можна використати як новий методичний апарат розрахунків повітропідігрівників, так і апарат для виявлення можливих удосконалень об’єкта.
Ключові слова: повітропідігрівник, математична модель, теплоносій, параметри, система.

It is inefficient to use known methods of designing and verification in solving operational problems when determining the influence of various operational changes on the performance of a boiler for air heating, since it is necessary to have a considerable amount of information that is difficult to obtain in operating conditions.
In this paper we propose a block diagram and the corresponding mathematical model of an air heating boiler as a system of interconnected heater exchangers which utilizes only data about incoming and outgoing water temperature in the initial mode. On the basis of operating mode calculations a mathematical model of the heat exchange system, based on a two-way heat exchanger was developed.
Application of the developed mathematical models allows for regime calculations of boilers' heating surfaces knowing only operational parameters
(such as coolant temperature in one of the modes of the equipment operation)
and objective parameters (coolant flow rate, area and condition of heating surfaces) may remain unknown.
Key words: air heating boiler, mathematical model, coolant, parameter, system.

Кількість посилань 6

УДК 62-501.72

І.М. Ковела, О.С. Вітер, Р.І. Стахів, Ю.В. Яцук
Національний університет “Львівська політехніка”

АВТОМАТИЗОВАНА ІДЕНТИФІКАЦІЯ ОБ’ЄКТІВ РЕГУЛЮВАННЯ ЗА ЇХ ЕКСПЕРИМЕНТАЛЬНИМИ ІМПУЛЬСНИМИ ХАРАКТЕРИСТИКАМИ

© Ковела І.М., Вітер О.С., Стахів Р.І., Яцук Ю.В., 2014

Пропонується новий метод отримання передавальних функцій об’єктів регулювання за їх експериментальними імпульсними характеристиками, який полягає у тому, що задача ідентифікації зводиться до математичної задачі апроксимації експериментальних даних аналітичними виразами і розв’язання її за допомогою інформаційних технологій.
Ключові слова: передавальна функція, апроксимація, інформаційні технології.

A new method to obtain the transfer functions of the objects based on their experimental impulse response is presented. The identification problem is reduced to a mathematical problem of approximation of experimental data by the analytic expressions and to solving it using information technologies.
Automatic processing of experimental impulse response in order to obtain the mathematical model of control object can be done in various ways. In certain studies the problem of identification using impulse response is solved by means of mathematical optimization techniques and by means of specialized software that is complicated and is restricted for practical use.
In order to address these shortcomings a new more versatile method of automated identification of objects by experimental impulse response is proposed in the paper.
The proposed method can effectively solve the vast majority of practical problems of identification of industrial facilities. The use of the impulse response has a number of advantages.
Key words: transfer function, approximations, information technologies.

Кількість посилань 10

УДК 526.521.3

А.Л. Корниенко, Л.Ф. Жуков
Физико-технологический институт металлов и сплавов НАН Украины

ИССЛЕДОВАНИЕ ИНСТРУМЕНТАЛЬНЫХ ПОГРЕШНОСТЕЙ МНОГОЦВЕТОВОЙ ЛИНЕЙНОЙ СИММЕТРИЧНО-ВОЛНОВОЙ ТЕРМОМЕТРИИ МЕТАЛЛИЧЕСКИХ СПЛАВОВ

© Корниенко А.Л., Жуков Л.Ф., 2014

На основі вивчених і найпоширеніших для металів і їх сплавів випромінювальних характеристик вольфраму у видимій і ближній інфрачервоній областях спектра досліджено вплив похибок вихідних вимірювань температур випромінювання на інструментальні похибки багатокольорової лінійної симетрично-хвильової термометрії. Доведено, що на відміну від відомих методів багатокольорової пірометрії, випромінювання похибки симетрично-хвильової термометрії не перевищують похибки вихідних вимірювань. Для забезпечення симетрично-хвильової термометрії необхідно виключати селективне поглинання зареєстрованого на робочих довжинах хвиль теплового випромінювання супутніми і спеціальними проміжними середовищами.
Ключові слова: багатокольорова лінійна симетрично-хвильова термометрія, вихідна температура випромінювання, похибка вимірювань, інструментальна та методична похибки, спектральні розподіли випромінювальної здатності металів та їх сплавів.

On the basis of the most studied and representative emission characteristics of tungsten for metals and their alloys in the visible and near-infrared regions of the spectrum, the effect of errors in the initial measurement of the radiation temperature in the instrument errors of multicolor linear symmetrical wave thermometry is investigated. It is proved that unlike the known methods of radiation pyrometry, the errors of multicolor wave symmetrically thermometry do not exceed the initial measurement error. To ensure symmetrical wave thermometry it is necessary to exclude the selective absorption recorded at the operating wavelength of thermal radiation related to intermediate and special environments.
Key words: multicolor linear symmetrical wave thermometry, the initial temperature of the radiation measurement error, instrumental and methodological errors, the spectral distribution of the emissivity of metals and their alloys.

Кількість посилань 6

УДК 697.331:697.341

А.А. Маліновський, В.Г. Турковський, А.З. Музичак
Національний університет “Львівська політехніка”

МЕТОДИКА ТА АЛГОРИТМИ НАЛАГОДЖЕННЯ ЕЛЕВАТОРНИХ ВУЗЛІВ ТЕПЛОВИХ МЕРЕЖ

© Маліновський А.А., Турковський В.Г., Музичак А.З., 2014

Вирішено питання забезпечення якісного і ефективного теплопостачання абонентів із приєднанням до теплової мережі через елеваторний вузол з врахуванням мережевого характеру задачі. У разі надлишку розрахункового тиску на вводі абонента параметри елеваторного вузла забезпечують необхідний коефіцієнт змішування, а параметри дросельної шайби – усунення надлишкового тиску. Для визначення параметрів елеваторного вузла і дросельної шайби розроблена їх спільна математична модель з коефіцієнтами впливу суміжних віток, адаптована до мережевого підходу теорії гідравлічних кіл. Запропонований алгоритм визначення цих параметрів. Для випадку недостатнього тиску на вводі абонента, коли нема змоги забезпечити нормативні обсяги циркуляції теплоносія в мережі абонента, запропоновано алгоритм визначення параметрів елеваторного вузла з умови забезпечення необхідного обсягу тепла абонентам.
Ключові слова: елеваторний вузол, коефіцієнт змішування, теорія гідравлічних кіл, гідравлічний режим.

The process of providing an efficient heating to customers with connection to heating network via mixing valve is presented in this paper, taking into account the network nature of the problem. In the event of excess pressure at the customer’s heat input the mixing valve parameters provide the required mixing ratio and the throttle plate parameters provide removal of excess pressure. To determine the parameters of the mixing valve and the throttle plate a common mathematical model with the influencing factors of related branches adapted to the network approach of the theory of hydraulic circuits was developed. The algorithm for determining these parameters is proposed. In case of insufficient pressure on the customer’s heat input when there is no possibility to provide regulatory throughflow of the heat carrier in the customer network, an algorithm for determining the parameters of mixing valve with the condition of the required amount of heat to subscribers is proposed.
Key words: mixing valve, mixing ratio, theory of hydraulic circuits, hydraulic regime.

Кількість посилань 8

УДК 621.181:620.197

Й.С. Мисак, Я.Ф. Івасик, Є.М. Якимів, Т.П. Коваленко, Н.М. Лашковська
Національний університет “Львівська політехніка”

МЕТОДИ ЗАХИСТУ ПОВЕРХОНЬ НАГРІВАННЯ КОТЛІВ ВІД КОРОЗІЇ ПІД ЧАС ЇХНЬОГО ПРОСТОЮВАННЯ

© Мисак Й.С., Івасик Я.Ф., Якимів Є.М., Коваленко Т.П., Лашковська Н.М., 2014

Розглянуто процес корозії зовнішніх поверхонь нагрівання водогрійних котлів ПТВМ-180 і КВГМ-180, а також котлів ТЕС під час простоювання їх у резерві та розроблено методи боротьби з нею, враховуючи конструктивні особливості устатку¬вання. Запропоновано заходи та схему для забезпечення оптимальних умов перебування котлів у резерві.
Ключові слова: водогрійний котел, поверхня нагрівання, корозія, втрати тепла, простоювання у резерві.

The problem of maintaining thermal power equipment in reserve is important and by solving this problem a significant contribution to reducing the use of electricity and thermal energy for its own needs at HPSs and increasing the lifetime of equipment will be provided.
Therefore, in this article, attention is devoted to the process of corrosion of external surfaces of heating boilers PTVM-180 and KVGM-180 during their downtime in reserve. Methods to remove the corrosion considering the design features of the equipment are developed.
On the basis of experimental studies it was found that heat losses during idle boilers in reserve depends on the design of boilers and their technical condition, temperature of network water and environment.
The measures are proposed to protect the surfaces of the heating boilers from corrosion when they are idle in reserve.
Thus, by increasing the reliability in operation of boilers, which is an important and complicated task, and by solving this problem a significant contribution to the optimization of one of the main sources of heat will be made.
Key words: hot water boiler, heating surface, corrosion, heat loss, downtime in reserve.

Кількість посилань 6

УДК 621.311.22

Й.С. Мисак, М.П. Кузик
Національний університет “Львівська політехніка”

СУШІННЯ ЗОВНІШНІХ ПОВЕРХОНЬ НАГРІВАННЯ КОТЛІВ ТП-10 ЗА ДОПОМОГОЮ ТЕПЛОТИ ЖИВИЛЬНОЇ ВОДИ

© Мисак Й.С., Кузик М.П., 2014

Розглянуто процедуру водяного миття і подальшого сушіння котла ТП-10. Термічне сушіння зовнішніх поверхонь нагрівання котла здійснюється подачею в його пароводяний тракт живильної води з загальностанційного трубопроводу.
Ключові слова: миття котлів, сушіння котлів.

Procedure of aquatic washing and subsequent drying of boilers TP-10 is presented. The thermal drying of external surfaces of heating of boilers is important for serving the steam-aquatic highway of feedwater from the station pipeline. The optimal parameters of the drying process, especially the speed and duration of feeding feedwater were determined.
Analytical dependences to describe the dynamics of change in humidity of the drying agent and the output of the gas boiler when turning on the exhauster were developed. Based on these results the time dependence of the removal of water from the boiler was defined.
The amount of moisture remaining in the thermal drying boiler TP-10 after its washing was determined. It is approximately 3200-4000 lbs.
Key words: washing of boilers, drying of boilers.

Кількість посилань 3

УДК 532.5.013.12:532.585

В.І. Орел, В.В. Чернюк
Національний університет “Львівська політехніка”

ГІДРАВЛІЧНИЙ ОПІР ВИПУСКНОЇ ТРУБКИ, ЯКА ВИСТУПАЄ ВСЕРЕДИНУ НАПІРНОГО РОЗПОДІЛЬНОГО ТРУБОПРОВОДУ

© Орел В.І., Чернюк В.В., 2014

Досліджено коефіцієнти місцевих гідравлічних опорів випускної трубки, яка виступає до осі напірного розподільного трубопроводу під прямим кутом.
Ключові слова: випускна трубка, розподільний трубопровід, коефіцієнт місцевого гідравлічного опору.

Analysis of literature sources has shown that only one of known formulae expresses the influence of dynamics of slip flow upon the coefficient of local hydraulic resistance of the part of an outlet which is protruded to the axis of a distributive pressure pipeline at a right angle. When there is no transitive flow rate in the distributive pressure pipeline, a formula for this coefficient is obtained as a function of Reynolds’ number. The importance of the obtained results of the investigation consists in the possibility of finding the ways and substantiation of the technique of reduction in non-uniformity of fluid dispensation from a distributive pressure pipeline at the expense of the reduction of values of coefficient of local hydraulic resistance of outlet tubes.
Key words: outlet tube, distributive pressure pipeline, coefficient of local hydraulic resistance.

Кількість посилань 12

УДК 681.121.84

Р.М. Федоришин, Є.П. Пістун, В.К. Савицький
Національний університет “Львівська політехніка”

ПІДВИЩЕННЯ ТОЧНОСТІ ОБЛІКУ ПРИРОДНОГО ГАЗУ ЗА ІМПУЛЬСНИХ РЕЖИМІВ РОБОТИ ВИТРАТОВИМІРНИХ ВУЗЛІВ НА ТЕПЛОГЕНЕРУЮЧИХ ОБ’ЄКТАХ

© Федоришин Р.М., Пістун Є.П., Савицький В.К., 2014

Проаналізовано імпульсні режими роботи систем обліку природного газу на теплогенеруючих об’єктах. Виконано моделювання системи обліку з імпульсними режимами протікання газу для визначення похибки вимірювання температури газу, зумовленої інерційністю термоперетворювача, та відповідних похибок вимірювання витрати та об’єму газу. Виконано аналіз результатів моделювання цих похибок та запропоновано шляхи їх зменшення для підвищення точності обліку природного газу.
Ключові слова: вимірювання, об’єм, природний газ, імпульсний режим, похибка.

The impulse regimes of operation of natural gas metering systems at heat generating plants are analyzed. Simulation of a metering system with impulse regimes of gas flow is carried out in order to define the error of gas temperature measurement caused by the inertia of the thermometer and the subsequent errors of gas flow rate and volume measurement. The simulation results are analyzed and the ways to minimize these errors are proposed in order to improve the accuracy of natural gas metering.
Key words: measurement, volume, natural gas, impulse regime, error.

Кількість посилань 8

Syndicate content